BCIT Thesis and other Required Graduate Degree Works | BCIT Institutional Repository

BCIT Thesis and other Required Graduate Degree Works

Pages

Hygrothermal performance of super-insulated double-stud wood frame wall assemblies
In cold climates, much of wood-frame building enclosure durability failures and indoor air quality issues stem mainly from excessive moisture within enclosure components and these issues are more pronounced in buildings with higher levels of thermal insulation, with frequent mold and fungal growth complications. Nevertheless, buildings have been increasing their insulation levels (and this trend is expected to continue) due to climate change, depleting natural resources, ever-rising energy prices and growing expectation for occupants’ comfort and health. Incorporation of insulation materials with higher moisture storage and buffering capacities and also employing vapour retarders that can let walls dry out to both interior and exterior spaces are potential solutions. While the hygrothermal behaviour of these insulation materials have been extensively tested in material labs and computer modeling projects, their actual performance in different climatic zones demands more field experimental studies. In this study, a field experiment was designed to assess hygrothermal behaviors of five highly insulated test wall panels under Marine climatic zone of, Burnaby, British Columbia. Full size wall panel specimens of ‘double-stud’ wood-frame were instrumented with moisture and temperature sensors and filled with Dense Cellulose Insulation (DCI) and Low-Density Spray Polyurethane Foam Insulation (LD SPFI) under different vapour control layer scenarios of 4-mil Polyethylene film, Smart Vapour Retarder (SVR), and none. All test panels were exposed to the 4 controlled indoor and the actual outdoor climates and their hygrothermal response was recorded and analysed from 01 Sept 2016 to 31 May 2017. The experimental results suggested DCI is a proper insulation material provided that it is equipped with a dedicated interior vapour barrier. The results also suggested while both DCI had LD SPF had acceptable moisture behaviour; DCI had slightly better performance than LD SPF. As for vapour control strategies, Smart Vapour Retarder (SVR) did not show an obvious advantage over 4-mil Polyethylene film and in some cases was slightly outperformed by polyethylene hygrothermally. As a general comment, the exterior sheathing board, plywood had the highest moisture activity and all other components, mainly the exterior and interior studs and plates remained in safe moisture ranges throughout the test period., Insulation, Dense Cellulose Insulation, Low-Density Spray Polyurethane Foam Insulation, Hygrothermal performance
Hygrothermal propertied of building materials at different temperatures and relative humidities
This research project investigated and measured a set of hygrothermal characteristics of several building materials commonly used across the North America. This study examined the behavior of building materials under various climate conditions other than what is proposed by the standards. Improving available standard test methods by using state-of-the-art equipment, enabled me to measure thermal conductivity, sorption isotherms, water vapor permeability and water absorption coefficient of tested materials under nine different combinations of temperatures from iv 3°C to 45°C and relative humidities from 50% to 90%. The results clearly present dependency of material properties on varying temperature and relative humidity. For example, thermal conductivity, vapor permeability and water absorption coefficients of all tested materials increased with respect to temperature, while the sorption isotherms of all materials decreased when temperature rose. The obtained results from this research can be utilized in Heat, Air and Moisture (HAM) modeling to improve effective and realistic analysis hygrothermal and energy performance of whole buildings.
Identifying temporal trends and mechanisms for successful reforestation on former agricultural land
This study investigates the outcomes of restoration efforts completed on retired agricultural land in Southwest Ontario. Sites acquired by the Nature Conservancy of Canada were planted to kickstart succession to native deciduous forests, but the results of the plantings are mixed. Analysis of soil conditions indicated that low levels of soil organic carbon were correlated to low water content and high density unfavourable for plant growth. Analysis of remotely sensed imagery was done to assess and compare vegetation cover to reference conditions at Walpole Island First Nation. Analysis revealed that successful restoration was dependent on multiple soil characteristics, but conditions correlated to higher total organic carbon favoured greater vegetation cover. Remote sensing data revealed that succession towards tree canopy development was accelerated compared to passive restoration, and a shaded understory was established approximately 8-12 years following restoration. Future work can expand on succession and the effects of other restoration treatments., Soil, Reforestation, NDVI, Agriculture, Restoration, Secondary succession
Investigating regeneration in a raised ombrotrophic bog after peat extraction
Burns Bog is a raised ombrotrophic bog in Delta, British Columbia and faced with myriad disturbances. This study is focused on the impact and restoration of peat extraction by the Atkins-Durbrow Hydropeat method. Depth to water table, relative abundance and distribution of vegetation, and the degree of peat decomposition at consistent-depth intervals were investigated to elucidate the status of passive and active ecological restoration in three fields previously harvested for peat approximately one decade apart and compared to a fourth unharvested field. Summary statistics, Redundancy Analysis, and regression were used to compare restoration status and trends in hydrology, vegetation composition, and peat accumulation. A lag period between cessation of harvest and implementation of restoration, coupled with rapid anthropogenic climate change, serve as impediments to restoration here. Intervention in the form of improved rainfall retention, assisted recolonization, and the introduction of nurse species are recommended to improve bog function and resiliency., Atkins-Durbrow Hydropeat method, Ditch blocking, Ecological restoration, Peat extraction, Raised ombrotrophic bog, Burns Bog
Model-based coupling of air and hydronic system operation in a high performance academic building
This research is motivated from preliminary teamwork on analyzing the “Performance Gap” of three high-performance buildings, which are currently under operation. All three buildings are facing operational challenges that are not unusual considering the complexity of their systems. However, evidence from design documents, an existing energy model, and operational data suggests that their performance is not entirely reflecting the design intent. This research follows the premise that there is a need to design buildings as systems-of-systems to be able to understand, interpret, quantify, design, and fine-tune the dynamic couplings between systems. This research was dedicated to a high-performance academic building (HPAB) – one of the above three buildings – as a case-study to gain understanding on the complexities of systems coupling, and learn and apply dynamic simulation-based systems coupling tools and methods. The main focus of the study is the classrooms because of the existing evidence on the significant impact of indoor environmental comfort on student performance in academic facilities. The HPAB case-study building incorporates, at the source side, ground-coupled water-to-water heat pumps (WWHP) and solar-thermal as primary means of heating, with boiler used as a backup source. Cooling is provided by the cold side of the WWHP system. On the demand side, heating and cooling are delivered via thermally active radiant floors; while air handling systems take care of the ventilation and de/humidification needs, and provide supplementary heating and cooling. The building was initially designed to rely on natural ventilation for summer cooling; however, designers realized that natural ventilation alone was not able to meet the building cooling demands in the summer. Nevertheless, the building has operable windows and a central atrium that seems to be collecting the air from the individual spaces and exhausting it after some heat recovery. The thermally active building is not adequately meeting the demands from some critical zones. Furthermore, the operation is not consistent with the reduced hours of summer operation of an academic building. These and other observations on the building indicate that the air and radiant systems are not operating in synergy. Existing industry practices in building controls systems, and the research literature show limited evidence of efforts to attempt to harmonize these two complementary systems. Simulation was used to re-create the HPAB building’s mechanical system response in two levels: a classroom-level model, and a Whole Building Energy Model (WBEM). The implementation was in EnergyPlus modeling software. Design documents, and historic operational data from the building automation system (BAS) were used for calibration. In this work, various features of Energy Management System (EMS) module of EnergyPlus has been utilized to create a responsive mechanical system control within the simulation. In the end, the typical responses of the building spaces could be accurately recreated in the simulation for both models. In the next step, testing different controls approaches – labelled as Strategies – and comparing them with defined comfort and stability metrics showed that harmonizing the air and radiant systems, in addition to increasing the consistency of the radiant system operation, results in improvement to the system operation without sacrificing the comfort. This research explores the challenges of employing a WBEM to assist building design decisions by accounting for the building dynamics and enabling the coupling and tuning of systems parameters and control strategies through simulation. The research demonstrates the benefits of improved operational control sequences that are more in tune with the building’s design intent.
Multi-objective optimization of high performance residential buildings using a genetic algorithm
Traditional methods of design and construction of residential buildings are common practice, and in most cases, are required by building codes. However, these design practices do not necessarily yield the most optimized designs in terms of cost, environmental impact, and occupant thermal comfort. Typically, the owner or investor hires an architect that designs the building based on the client’s requirements, and then technical designs, such as enclosure and HVAC systems, are tasked to construction and mechanical engineers to satisfy the original design without consideration to energy consumption and environmental impacts. Those who are energy and environmentally conscious rely on an iterative trial and error method using energy simulation tools, and this method consumes much time and resources. To address this problem, this research presents the development and implementation of a simulation-based optimization tool that relies on a genetic algorithm to systematically improve the building design at a conceptual stage based on a set of objective functions. For the purpose of this research, the objective functions include the life-cycle costs, life-cycle global warming potential, and occupant thermal comfort. More specifically, occupant thermal comfort (measured in PPD) acts that the constraint objective. In this study, a multi-objective optimization genetic algorithm was implemented to find optimal residential building enclosure assemblies that minimizes the life-cycle costs, life-cycle global warming potential, and keeps occupant thermal comfort within check. Based on the design variables and objective functions, a software tool consisting of four modules is used for optimization: the input and input parameter database files; the genetic algorithm optimization software (jEPlus+EA); the energy simulation program (EnergyPlus) and the optimized output files. All required software and simulation programs can be acquired free of charge from the internet, with the exception of proprietary database files such as material and construction assembly libraries. For validation, the optimization tool is implemented on a benchmark study, which demonstrates its application and capabilities. The benchmark study is based on ANSI/ASHRAE Standard 140-2001 BESTEST calibration and validation test case 600. The optimization results in multiple Pareto optimal solutions that gives the user a detailed look at the trade-off between the objective functions when high performance building systems are used. The optimization tool is then applied to a case study where an actual single family home (Harmony House) is modeled and important building design parameters are identified and discussed., Multi-objective building optimization, Life Cycle Cost Analysis (LCCA), Life Cycle Environmental Assessment (LCEA), Green buildings, Building assessment methods
Performance evaluation of active chilled beam in cooling and heating operation under actual field boundary conditions
People spend most of their time indoors and often share the same environment; therefore, knowledge and prediction of the indoor conditions are important to optimize the indoor conditions for the occupants at the building design phase. A range of parameters like air velocity, temperature and relative humidity determines the indoor climate and are important for the comfort of the occupant of a room in terms of thermal comfort and indoor air quality. Active Chilled Beam (ACB), a high-performance air distribution system has gained popularity as an energy efficient, sustainable comfort cooling technology with favourable performance in term of thermal comfort to occupants. ACB is wildly utilized in a variety of commercial buildings, schools, laboratories and hospitals. However, in-depth investigations on the performance of these systems under different boundary conditions are still inadequate., Active chilled beam, ACB under cooling, ACB under heating, CFD, Room airflow, Ventilation efficiency
Phytoremediation of contaminated soils
Phytoremediation poses an ecologically friendly and cost-effective alternative to other remediation methods such as chemical or thermal treatment. However, in contaminated sites such as retired oil wells and brine spills, it is common to have a co-contamination of salt and polyaromatic hydrocarbons (PAHs). The co-contamination of salt and PAHs may decrease the rate and effectiveness of bioremediation. Here we investigated the effect soil salinity has on the rate of phytoremediation, plant survivability and biomass. A 90-day greenhouse study was performed, growing alfalfa (Medicago sativa L.) in soils treated with varying salt (NaCl) concentrations in the presence of pyrene and benzo[a]pyrene. No significant differences were observed in the presence or absence of PAHs. Salt treatments has significant affects on plant biomass, nodulation, and successful germination., Bioremediation, Polyaromatic hydrocarbons, Alfalfa, Salt, Phytoremediation
Plant facilitation effects as a potential restoration tool in riparian ecosystems in Southwestern British Columbia
This study began to investigate potential facilitative effects among shrub species in riparian ecosystems in southwestern British Columbia. I ran two concurrent studies. Six plots for each of four treatments were established at the Coquitlam River Wildlife Management Area. The first two treatments compared the survival, growth, flowering, and herbivory rates of planted twinberry seedlings in plots where the shrub layer was removed to plots where it was not. The other two treatments compared the survival, growth, leaf loss, flowering and herbivory rates of snowberry plants in plots where the salmonberry upper shrub layer was removed to those where it was not. No significant differences between the measured parameters in any of the treatments were found. These results are discussed in the context of the riparian forest ecosystem and current facilitation theory. The results are then used to inform an ecological restoration plan for the Suwa’lkh School Forest., Facilitation, Riparian forests, Native vegetation, Symphoricarpos albus, Lonicera involucrate, Rubus spectabilis, Ecological restoration
RC-network based transient calculation method for thermal bridge analysis of multi-dimensional assemblies
Hourly dynamic energy performance study of buildings requires an in-depth understanding of dynamic thermal performance of building envelope assemblies. While two and three-dimensional building envelope thermal bridges have a great impact on whole-building energy simulations, heat storage capacity of the layers has also a significant influence. State of the art research has confirmed necessity of accurate thermal storage behavior analysis of building envelope assemblies in dynamic hourly building energy simulations. To-date, a number of studies have been conducted on the simplification of transient behaviour prediction of one, two and three-dimensional building envelope assemblies. In this study, the previous equivalent and simplified models for prediction of dynamic behaviour of building enclosure are reviewed, and an improved equivalent model based on frequency responses of RC-Network (FR-RCN) is presented. The model utilizes thermal RC-Network with three unknown resistances, two known resistances, and four unknown capacitances. The frequency responses of building envelope assembly are calculated either analytically (one dimensional assemblies), or numerically using COMSOL (two/three dimensional assemblies). Eureqa, a software which leverages evolutionary algorithms, is utilized in order to generate optimized unknown RC-Network resistances and capacitances considering the calculated frequency responses of the assembly. In this study, one light weight single-family home, one mass type structure high-rise building, and selected steel construction assemblies in climate zones 2 and 6 have been considered. A simple approach is also presented for the generation of equivalent FR-RCN models of variable insulation thickness assemblies. The comparison between the transient results calculated from the equivalent FR-RCN and COMSOL simulation shows good agreement. The performance of FR-RCN method is compared with other selected equivalent models, and an improvement in accuracy is confirmed., RC-Network, Multi-dimensional assemblies
Restoration of old forest characteristics in a 1957 spacing trial in the Malcolm Knapp Research Forest, British Columbia
Forest managers are interested in determining how stands that have been logged might be managed to restore features characteristic of forests in later-stages of development. Incorporating forest restoration into forest management enables the use of forest-management skills, such as silviculture and regeneration techniques, to manage individual stands for multiple objectives. Therefore, I performed a comparative analysis of large trees, very-large trees, large snags, very-large snags, and large CWD among three stand types (i.e., 60-yr-managed, 140-yr-natural, and 500-yr-natural stands). The 140-yr-natural and 500-yr-natural stands were used as reference conditions to guide the restoration of a 59-yr-managed spacing trial. All attributes differed among stand-types; however, large snags were the most similar attribute between 140-yr-natural and 500-yr-natural stands. Large trees were the fastest attribute to recover in 60-yr-managed stands, however mean values among stand-types still differed. This study highlights the potential of restoring old-natural attributes in younger-managed stands to increase ecological resiliency., forest, natural, managed, prescription, restoration, old-natural attributes
Sound living in Vancouver's laneway housing
Laneway housing is an innovative higher density housing form introduced to meet the City of Vancouver’s EcoDensity Charter. This form of residential occupancy was introduced without specific acoustical standards for construction. Noise concerns generally accompany increasing urban density, particularly in housing located close to transportation and activity centers. Laneways and laneway housing have environmental and architectural features that can contribute to noise levels exceeding criteria for healthy living. To advance the state of practice, this research first explores the sonic environment of laneways, including sound propagation, urban canyon effects, and sound sources. Second, this research investigates the acoustics of the laneway house, including outdoor-indoor sound insulation of facades, architectural features, and floor plan layout in relation to environmental noise sources. Empirical field measurements, the CMHC road traffic noise model and software modelling programs are used to investigate the acoustical environmental quality of laneway housing. Findings from case study investigation of four laneways and six laneway houses are evaluated against the CMHC noise criteria for healthy living. The various research tools are evaluated for accuracy and practicality as acoustic design tools for Vancouver laneways and laneway housing. The results of this study can inform laneway development planning (including benefits of laneway vegetation), laneway house design, building envelope construction, and policy guidelines as the City of Vancouver continues in its plans for sustainable densification., Acoustics of small buildings, Urban canyon effect, Road traffic noise, Laneway house acoustics

Pages