BCIT Citations Collection | BCIT Institutional Repository

BCIT Citations Collection

Pages

Determination of hydrastine and berberine in goldenseal raw materials, extracts, and dietary supplements by high-performance liquid chromatography with UV
A multilaboratory collaborative study was conducted on a high-performance liquid chromatographic (HPLC) method utilizing UV detection, previously validated using AOAC single-laboratory validation guidelines for determination of hydrastine and berberine in goldenseal (Hydrastis canadensis L.) raw materials, extracts, and dietary supplements at levels ranging from 0.4 to 6% (w/w). Nine collaborating laboratories determined the hydrastine and berberine content in 8 blind samples. Sample materials included powdered botanical raw materials, whole root material, and 4 finished product dietary supplements containing either goldenseal powdered root material or extract. The materials were extracted with an acidified water and acetonitrile solution. HPLC analyses of the extracts were performed on a C18 column using UV detection at 230 nm. Results for powdered root material and capsule products ranged from about 0.2% (w/w) for each alkaloid to about 4% (w/w) for each alkaloid. Liquid tincture results were approximately 4000-5000 microg/mL for each alkaloid. Reproducibility relative standard deviations (RSDR) for hydrastine ranged from 2.68 to 6.65%, with HorRat values ranging from 0.77 to 1.89. RSDR for berberine ranged from 5.66 to 7.68%, with HorRat values ranging from 1.32 to 2.12. All finished products containing goldenseal extract yielded HorRat values <2.0. Based on these results, the method is recommended for Official First Action for determination of hydrastine and berberine in goldenseal raw materials and dietary supplement finished products containing powdered goldenseal and goldenseal extract., Peer-reviewed article, Published.
Determination of major phenolic compounds in Echinacea spp. raw materials and finished products by high-performance liquid chromatography with ultraviolet detection
A method previously validated to determine caftaric acid, chlorogenic acid, cynarin, echinacoside, and cichoric acid in echinacea raw materials has been successfully applied to dry extract and liquid tincture products in response to North American consumer needs. Single-laboratory validation was used to assess the repeatability, accuracy, selectivity, LOD, LOQ, analyte stability (ruggedness), and linearity of the method, with emphasis on finished products. Repeatability precision for each phenolic compound was between 1.04 and 5.65% RSD, with HorRat values between 0.30 and 1.39 for raw and dry extract finished products. HorRat values for tinctures were between 0.09 and 1.10. Accuracy of the method was determined through spike recovery studies. Recovery of each compound from raw material negative control (ginseng) was between 90 and 114%, while recovery from the finished product negative control (maltodextrin and magnesium stearate) was between 97 and 103%. A study was conducted to determine if cichoric acid, a major phenolic component of Echinacea purpurea (L.) Moench and E. angustifolia DC, degrades during sample preparation (extraction) and HPLC analysis. No significant degradation was observed over an extended testing period using the validated method., Peer-reviewed article, Published.
Determination of mitragynine in mitragyna speciosa raw materials and finished products by liquid chromatography with UV detection
Mitragyna speciosa (kratom) is a tree indigenous to Southeast Asia, and its leaves are used in herbal formulations because they contain indole alkaloids mitragynine and 7-hydroxy (7-OH) mitragynine. An HPLC method was developed, optimized, and validated using single-laboratory validation guidelines to quantify mitragynine in kratom raw materials and finished products. The method optimization evaluated several extraction parameters including solvent type, solvent volume, time, and extraction method. The separation of the mitragynine alkaloids was achieved in 18 min with a fused-core C18 EVO column using gradient separation with ammonium bicarbonate (pH 9.5) and acetonitrile. The calibration range for mitragynine was 1.0–500 μg/mL with correlation coefficients of ≥99.9% throughout method development and validation. The method detection limit and LOQ were 0.2 and 0.6 μg/mL, respectively for mitragynine. Eight test samples were obtained to evaluate method repeatability. RSDr ranged from 0.4 to 1.0%, whereas intermediate precision ranged from 3.7 to 7.3%, with HorRat values from 0.68 to 1.96. 7-OH mitragynine was below the LOQ for all samples, therefore, spikes repeatability sample RSD values were <1%. The validation data presented meet the Standard Method Performance Requirements as specified by the AOAC INTERNATIONAL Kratom Working Group., Peer-reviewed article, Published. Received July 12, 2016; Accepted by AP September 12, 2016.
Determination of phenolic constituents in echinacea raw materials and dietary supplements by HPLC-UV
A collaborative study was conducted to evaluate an HPLC method for determining phenolic compounds in Echinacea spp. raw materials, powdered extracts, and tinctures. Eleven collaborating laboratories received three practice samples representing each matrix type, phenolic reference standards, eight test samples as blind duplicates, the validated analytical method, and instructions. Test samples included two raw materials, four extracts (including one in combination with astragalus and reishi), one ethanolic tincture in combination with goldenseal, and one glycerite tincture. Each material was extracted with a 60% methanol aqueous solution, separated on a C18 column, and detected at 330 nm. Results reported by laboratories for total phenolics in Echinacea roots, aerial parts, and extracts ranged from 9.5 to 62.9 mg/g with RSDR ranging from 3.64 and 7.95% and Horwitz ratio (HorRat) values ranging from 1.06 to 2.01. Total phenolics in the ethanolic tincture ranged from 4837 to 5962 μg/mL, with an RSDR of 6.35% and a HorRat value of 1.45. The glycerite tincture showed poor interlaboratory precision with a HorRat value of 3.32, an RSDR of 21.8%, and reported total phenolic values ranging from 257 to 539 μg/mL., Peer-reviewed article, Published. Received May 4, 2016; Accepted by AP May 25, 2016.
Determination of β-N-methylamino-L-alanine, N-(2-aminoethyl)glycine, and 2,4-diaminobutyric acid in food products containing cyanobacteria by ultra-performance liquid chromatography and tandem mass spectrometry
A single-laboratory validation study was completed for the determination of β-N-methylamino-L-alanine (BMAA), N-(2-aminoethyl)glycine (AEG), and 2,4-diaminobutyric acid (DAB) in bulk natural health product supplements purchased from a health food store in Canada. BMAA and its isomers were extracted with acid hydrolysis to free analytes from protein association. Acid was removed with the residue evaporated to dryness and reconstituted with derivatization using 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate (AccQ-Fluor). Chromatographic separation and detection were achieved using RP ultra-performance LC coupled to a tandem mass spectrometer operated in multiple reaction monitoring mode. Data from biological samples were evaluated for precision and accuracy across different days to ensure repeatability. Accuracy was assessed by spike recovery of biological samples using varying amino acid concentrations, with an average recovery across all samples of 108.6%. The analytical range was found to be 764-0.746 ng/mL prior to derivatization, thereby providing a linear range compatible with potentially widely varying analyte concentrations in commercial health food products. Both the U. S. Food and Drug Administration (FDA) and U. S. Pharmacopeia definitions were evaluated for determining method limits, with the FDA approach found to be most suitable having an LOD of 0.187 ng/mL and LLOQ of 0.746 ng/mL. BMAA in the collected specimens was detected at concentrations lower than 1 μg/g, while AEG and DAB were found at concentrations as high as 100 μg/g. Finding these analytes, even at low concentrations, has potential public health significance and suggests a need to screen such products prior to distribution. The method described provides a rapid, accurate, and precise method to facilitate that screening process., Peer-reviewed article, Published. Received April 15, 2015; Accepted by SG June 22, 2015.
Development and evaluation of an affordable lift device to reduce musculo-skeletal injuries among home support workers
Home support workers (HSWs) work in clients’ homes assisting with rehabilitation and activities of daily living. Like all health-care professionals, HSWs are at an increased risk for developing back injuries. Lift devices have been shown to reduce injuries to the worker. Presently, there are few lifting devices for home use that cost under $4000 CDN. Our study involved designing a safe and affordable lift device (retail cost under $2000 CDN) to be used by HSWs in the home and evaluating it in a typical bathroom. Thirty-eight HSWs and three seniors evaluated the BCIT lift, a commercially available lift (BHM Medical Inc.) and the manual method of transfer and lift. Results indicated that the BCIT lift was an improvement over the manual method of transferring, and approximated the more expensive, automatic lift in terms of perceived exertion, ease of use and safety. Feedback provided to the researchers has been incorporated into a new, ergonomically sound and marketable lift device., Peer-reviewed article, Published. Received 1 February 2003, Revised 27 January 2004, Accepted 23 February 2004, Available online 6 May 2004.
Development of a lightweight low-carbon footprint concrete containing recycled waste materials
Use of any recycled material helps to maintain a greener environment by keeping waste materials out of the landfills. Recycling practices also can decrease the environmental and economical impact of manufacturing the materials from virgin resources, which reduces the overall carbon footprint of industrial materials and processes. This study examined the use of waste materials such as crushed glass, ground tire rubber, and recycled aggregate in concrete. Compressive strength and elastic modulus were the primary parameters of interest. Results demonstrated that ground tire rubber introduced significant amounts of air into the mix and adversely affected the strength. The introduction of a defoamer was able to successfully remove part of the excess air from the mix, but the proportional strength improvements were not noted implying that air left in the defoamed mixture had undesirable characteristics. Freeze-thaw tests were next performed to understand the nature of air in the defoamed mixtures, and results demonstrated that this air is not helpful in resisting freeze-thaw resistance either. Overall, while lightweight, low-carbon footprint concrete materials seem possible from recycled materials, significant further optimization remains possible., Peer-reviewed article, Published. Received 4 April 2011; Revised 27 July 2011; Accepted 27 July 2011.
Development of an integrated staircase lift for home access
Purpose: Stairways into buildings present a significant environmental barrier for those with mobility impairments. A number of home access solutions that allow users to safely enter and exit the home exist; however, these all have some limitations. The purpose of this work was to develop a novel, inclusive home access solution that integrates a staircase and a lift into one device. Method: We developed an integrated staircase lift following a structured protocol with stakeholders providing feedback at various stages in the design process, consistent with rehabilitation engineering design methods. Results: A novel home access device was developed. The integrated staircase-lift has the following features: inclusivity, by a design that provides an option for either use of stairs or a lift; constant availability, with a lift platform always ready for use on either level; and potential aesthetic advantages when integrating the device into an existing home. The potential also exists for emergency descent during a power outage, and self-powered versions. Conclusions: By engaging stakeholders in a user-centred design process, we were able to gain insight into the limitations of existing home access solutions and get specific feedback on our lift concept. This information strengthened the development of a novel home access device., Peer-reviewed article, Published. Article first published online: July 16, 2015; Issue published: October 26, 2015.
Dynamic regulation of growing domains for elongating and branching morphogenesis in plants
With their continuous growth, understanding how plant shapes form is fundamentally linked to understanding how growth rates are controlled across different regions of the plant. Much of a plant's architecture is generated in shoots and roots, where fast growth in tips contrasts with slow growth in supporting stalks. Shapes can be determined by where the boundaries between fast- and slow-growing regions are positioned, determining whether tips elongate, branch, or cease to grow. Across plants, there is a diversity in the cell wall chemistry through which growth operates. However, prototypical morphologies, such as tip growth and branching, suggest there are common dynamic constraints in localizing chemical growth catalysts. We have used Turing-type reaction-diffusion mechanisms to model this spatial localization and the resulting growth trajectories, characterizing the chemistry-growth feedback necessary for maintaining tip growth and for inducing branching. The mechanism defining the boundaries between fast- and slow-growing regions not only affects tip shape, it must be able to form new boundaries when the pattern-forming dynamics break symmetry, for instance in the branching of a tip. In previous work, we used an arbitrary concentration threshold to switch between two dynamic regimes of the growth catalyst in order to define growth boundaries. Here, we present a chemical dynamic basis for this threshold, in which feedback between two pattern-forming mechanisms controls the extent of the regions in which fast growth occurs. This provides a general self-contained mechanism for growth control in plant morphogenesis (not relying on external cues) which can account for both simple tip extension and symmetry-breaking branching phenomena., Peer-reviewed article, Published. Received 7 December 2011, Revised 6 March 2012, Accepted 21 March 2012, Available online 28 March 2012.
Dynamic wheelchair seating positions impact cardiovascular function after spinal cord injury
Innovative wheelchairs allow individuals to change position easily for comfort and social situations. While these wheelchairs are beneficial in multiple ways, the effects of position changes on blood pressure might exacerbate hypotension and cerebral hypoperfusion, particularly in those with spinal cord injury (SCI) who can have injury to autonomic nerves that regulate cardiovascular control. Conversely, cardiovascular benefits may be obtained with lowered seating. Here we investigate the effect of moderate changes in wheelchair position on orthostatic cardiovascular and cerebrovascular reflex control.Nineteen individuals with SCI and ten neurologically-intact controls were tested in supine and seated positions (neutral, lowered, and elevated) in the Elevation™ wheelchair. Participants with SCI were stratified into two groups by the severity of injury to cardiovascular autonomic pathways. Beat-to-beat blood pressure, heart rate and middle cerebral artery blood flow velocity (MCAv) were recorded non-invasively.Supine blood pressure and MCAv were reduced in individuals with lesions to autonomic pathways, and declined further with standard seating compared to those with preserved autonomic control. Movement to the elevated position triggered pronounced blood pressure and MCAv falls in those with autonomic lesions, with minimum values significantly reduced compared to the seated and lowered positions. The cumulative duration spent below supine blood pressure was greatest in this group. Lowered seating bolstered blood pressure in those with lesions to autonomic pathways.Integrity of the autonomic nervous system is an important variable that affects cardiovascular responses to orthostatic stress and should be considered when individuals with SCI or autonomic dysfunction are selecting wheelchairs.This work was supported in part by the Heart and Stroke Foundation of British Columbia and the Yukon (V.E.C)., Peer-reviewed article, Published. Received: December 14, 2016 ; Accepted: June 12, 2017 ; Published: June 30, 2017
An eco-friendly scheme to eliminate silica problems during bamboo biomass fractionation
In this study, an eco-friendly scheme to resolve the silica associated challenges encountered in processing bamboo for biorefineries was evaluated. Bamboo chips were pretreated with sodium hydroxide (NaOH) at low temperature to completely extract silica and partially extract hemicelluloses for follow up conventional kraft pulping or bioethanol production. Silica and hemicellulose in the alkaline pre-extraction liquor (APEL) were sequentially isolated through carbon dioxide (CO2) and ethanol precipitation. High purity (> 99.8%) amorphous silica particles were recovered by carbonating the effluent at 60oC to a pH of 8.2 with CO2. The CO2 adsorption capacity of the APEL was determined to be 7.15g CO2 per liter. After recovering more than 96% of available silica in the APEL, hemicellulose in the CO2-treated liquor was subsequently separated. This study demonstrated the feasibility of pre-extraction and recovery of silica and hemicellulose to alleviate the silica challenges, thereby allowing to expand bamboo as a feedstock for industrial processes., Peer-reviewed article, Published. Manuscript received October 11, 2016; Accepted December 12, 2016.
Ecological footprints and lifestyle archetypes
The global urban transition increasingly positions cities as important influencers in determining sustainability outcomes. Urban sustainability literature tends to focus on the built environment as a solution space for reducing energy and materials demand; however, equally important is the consumption characteristics of the people who occupy the city. While size of dwelling and motor vehicle ownership are partially influenced by urban form, they are also influenced by cultural and socio-economic characteristics. Dietary choices and purchases of consumable goods are almost entirely driven by the latter. Using international field data that document urban ways of living, I develop lifestyle archetypes coupled with ecological footprint analysis to develop consumption benchmarks in the domains of: food, buildings, consumables, transportation, and water that correspond to various levels of demand on nature’s services. I also explore the dimensions of transformation that would be needed in each of these domains for the per capita consumption patterns of urban dwellers to achieve ecological sustainability. The dimensions of transformation needed commensurate with ecological carrying capacity include: a 73% reduction in household energy use, a 96% reduction in motor vehicle ownership, a 78% reduction in per capita vehicle kilometres travelled, and a 79% reduction in air kilometres travelled., Peer-reviewed article, Published. Received: 20 December 2014 ; Revised: 15 March 2015 ; Accepted: 8 April 2015 ; Published: 21 April 2015.

Pages